StarMax Starlink Gen 3 Router Wall Mount — Black 3D-Printed Bracket
StarMax Starlink Gen 3 Router Wall Mount — Black 3D-Printed Bracket
The StarMax Gen 3 router wall mount is a black 3D-printed bracket that holds the Starlink Gen 3 WiFi router flat against a wall. The router sits in a moulded cradle held at both ends, the bracket fixes to the wall with two countersunk screws, and the whole assembly projects only slightly from the wall so the router looks deliberate rather than parked.
What does this bracket fit?
| Hardware | Compatible | Notes |
|---|---|---|
| Starlink Gen 3 WiFi router (V3) | Yes | Shaped to this router's housing |
| Gen 2 router (UTR-211) | No | Different body — we make a separate mount |
| Starlink Mini | No | The Mini has no separate router |
| Gen 3 power supply | No | Separate bracket — see the combo |
Surfaces: plasterboard, timber, brick or masonry with the appropriate fixings; also van and RV walls, cabinets, cupboards and equipment boards.
Specifications
| Fits | Starlink Gen 3 WiFi router (V3) |
| Colour | Black |
| Manufacture | 3D printed in-house by StarMax |
| Design | StarMax original |
| Fixing | Two countersunk wall screw holes |
| Orientation | Router sits upright in the cradle |
| Ventilation | Vents and status light left clear |
| Cable routing | Cables exit down the back of the bracket |
Why buy this bracket
- Gets the router off the floor — wall-mounted, out of the way, and it looks intentional.
- Vents and status light stay clear — the cradle holds the router at its edges, nothing is covered.
- Slim against the wall — projects only a little, so it does not dominate the room.
- Two-screw installation — countersunk holes, a few minutes with a drill.
- Cables run down the back — no loop of cable across the worktop.
- Nothing attached to the router — no adhesive, no clips, no marks; it lifts straight out.
- StarMax original design — our own geometry, 3D printed in-house.
- Ships in 24 hours, free shipping, 30-day returns.
Who is this bracket for?
This bracket suits you if the router is sitting on the floor or balanced on a shelf; if you are building a tidy equipment board in a utility room, cupboard or van; if you want the cables off the worktop; if you have children or pets who knock things over; or if you are doing a permanent install and want it to look considered.
What is included
Included: 1 × StarMax wall mount bracket, black.
Not included: the Starlink Gen 3 router, wall screws or plugs, the Gen 3 power supply (see our combo).
Frequently asked questions
Does the router overheat in the bracket?
No. The cradle holds the router at its edges, so the vents and the surfaces that shed heat stay open to the air.
Will it fit the Gen 2 router?
No. The Gen 2 router has a different body and needs its own bracket, which we also make.
What screws do I need?
Two screws suited to your wall — plasterboard anchors for stud walls, wall plugs for masonry, or wood screws into timber. The holes are countersunk so the heads sit flush.
Can I take the router out?
Yes, it lifts straight out of the cradle. Nothing clips, glues or clamps to the router itself.
Can I fit it in a van or RV?
Yes, and it is one of the more common uses. Fix into a solid panel or use suitable anchors, since a moving vehicle puts more load on the fixings than a house wall.
Is this a Starlink product?
No. It is a StarMax original design, 3D printed by us — an aftermarket accessory made to fit the Gen 3 router. We are an independent maker, not affiliated with SpaceX.
StarMax is an independent designer and maker of aftermarket accessories for Starlink® hardware. This product is not manufactured, sold or endorsed by SpaceX. Starlink® is a trademark of Space Exploration Technologies Corp.